TPA transport anchor
Technical specifications
| Spread anchor TPA-FS / Columns, beams, trusses, wall elements, π-slabs / Component thickness, concrete grade, reinforcement / Load class 1,4 – 22,0 |  |
| Two hole anchor TPA-FZ / Prestressed concrete trusses, thin-wall elements, low strength concrete (e.g. lightweight concrete)/Component thickness,concrete grade, reinforcement/ Load class 1,4 – 26,0 |  |
| Erection anchor TPA-FA/ Thin-wall concrete elements, eing lifted from a horizontal to a perpendicular position/Component thickness, concrete grade, reinforcement/ Load class 1,4 – 22,0 |  |
| Unilateral erection anchor TPA-FE/ Thin-wall concrete elements, being lifted from a horizontal to a perpendicular position/Component thickness, concrete grade, reinforcement/ Load class 1,4 – 22,0 |  |
| Plate anchor TPA-FP/Very thin ceiling slabs with surface-embedded anchors/Component thickness, concrete grade, reinforcement/ Load class 1,4 – 10,0 |  |
| Garage anchor TPA-FG / Precast concrete garages, embedding in floor or ceiling slabs/ Component thickness, concrete grade, reinforcement/ Load class 4 |  |
| Flat foot anchor TPA-FF/ Ceiling slabs with surfaceembedded anchors, tubes/ Component thickness, concrete grade, reinforcement/ Load class 1,4 – 22,0 |  |
| Double ended column anchor TPA-FD/Columns / Component thickness, concrete grade, reinforcement/ Load class 2,5 – 26,0 |  |
| Sandwich panel anchor TPA-FX/ Sandwich panels/Component thickness, concrete grade, reinforcement/Load class 2,5 – 17,0 |  |
| Universal anchor TPA-FU/ see TPA-FS, TPA-FZ and TPA-FA/ Component thickness, concrete grade, reinforcement/ Load class 1,25 |  |
| TPA-A-1/ Plastic / For all anchors except TPA-FU and TPA-FG/ Holding plates H1, H2, HM; holding bolts S1 oder S2/ High durability and good resistance to formwork treatment agents / Load class 2,5 – 26,0 |  |
| Ring clutch TPA-R1/ With shackle/ For manual release / Load class 2,5 – 26,0 |  |
| Ring clutch TPA-R2/ With wire cable/ For manual release/ Load class 1,25 – 10,0 |  |
| Ring clutch TPA-R3/ With wire cable/ For manual release/ Load class 26,0 |  |
Benefits
- 15 load classes from 0.7 to 26.0
- numerous types of ancho
- Confusion of load classes not possible, because only those components that belong together fit together
- Erection anchors protect the concrete when shear loads are applied
- CE-marking
Applications
- The anchor The anchors are made from a special quality of flat steel. The anchor head has a hole in which the locking ring of the clutch can engage. A visible manufacturers mark is embossed on each anchor; this contains the product brand FRIMEDA (FR) with the system name (F), the anchor type (e.g. S), the length of the anchor in cm (e.g. 13) and the load class (e.g. 2.5). Ring clutches The ring clutch is positioned in the recess surrounding the cast-in anchor and the locking latch is closed by hand, enabling the locking ring to engage with the anchor head. The clutch is thus connected with the anchor in a matter of seconds. The ring clutch can now be pulled in all directions to allow for lifting, rotating and pitching of the unit. There is no preferred direction. To release, open the latch and the ring clutch can be removed. For cases where access is difficult (see accident prevention regulations (UVV)) remote control operated ring clutches are available (TPA-F1, TPA-F2).
Engineering services
- Based on the technical requirements of the customer, our engineers will calculate the appropriate element and provide the calculation of the loads in accordance with the standards.
- On the website is available software with which you can easily calculate the desired configuration of the HDB element.
- Our engineers will provide technical support and advise the customer’s specialists both before and during installation work.